C.R.Laurence
Il vostro conto  Vedere il carrello  AccediEsci

Catalog Number: 1217349


  • Easy Gunning
  • Meets or Exceeds U.S. Federal Motor Vehicle Safety Standards 208 and 212

  • Screw-On V-Cut Nozzles
  • Value Priced, Fast Curing, Cold Applied

  • Part of the LYNX Services Program
  • Guide to Proper Installations

    		•

    CRL POWR BOND Hi-Viscosity Urethane Adhesive is a fast curing adhesive that passes or exceeds U.S. Federal Motor Vehicle Safety Standards FMVSS212 (Barrier Crash Test) and FMVSS208 (Occupant Crash Protection) in its most severe interpretation with dual air bags and unrestrained dummies. The fast curing formula is tack free in only 50 ±10 minutes and offers Safe Drive Away Time in as little as 1-1/2 hours when used on vehicles without a passenger side air bag, 3 hours with passenger air bag at 73°F (23°C) and 45% RH (relative humidity).



    CRL POWR BOND Hi-Viscosity Auto Glass Urethane Adhesive - 10.1 Fl. Oz. Cartridge


    		 


    Altri prodotti/finiture:

    Numero articolo:1217349
    Disponibile anche in questi cataloghi:
    TV12A Truck & Van Accents 2011, PAGINA AC45
    CRL03 Sealants, Adhesives, and Fasteners, PAGINA N482
    1217349 has been superseded by Catalog Number: PP301HV. To view the replacement item, Click here

    Cleaning and Primers: CRL Urethanes are supported by a one-step primer and aerosol cleaner formulated for use in all aspects of glass bonding, including the glass frit, pinchweld, and EPDM/PVC moldings.

    1. After removing all of the old urethane to within 1/16" (1.5 mm) of the pinchweld, prepare the pinchweld following the procedures outlined in the CRL Technicians Training Manual. Prime these areas with 1214006 One Step Primer.

    2. Clean the inside of the windshield with a lint-free towel 1550 and PWR22 Automotive Glass Cleaner.

    3. Apply the same 1214006 One Step Primer to the frit area with a lint-free towel and allow to dry for a minimum of 10 minutes, but no more than 8 hours before installing the adhesive. This procedure must be performed above 40°F (4°C). NOTE: One Step Primer must be used prior to any adhesive application to prevent glass displacement. Failure to do so may result in personal injury or property damage.

    4. Apply 1214006 One Step Primer to encapsulated moldings if they are part of the bonding area.

    Packaged in metal cartridges with 4-1/2" (114 mm) long screw-on Cone Nozzles included in every case. 12 cartridges per case.

    For use by trained applicators only. Please refer to CRL Technician Training Manual, Technical Spec Data Sheet and Material Safety Data Sheet before using product. Cat. No. 1214006 One Step Primer must be used prior to any adhesive application to prevent glass displacement. Failure to do so may result in personal injury or property damage. Store cartridges closed and upright when not in use. Store between 65°F (18°C) and 75°F (24°C) in dry conditions. IMPORTANT: CRL9P and CRL9GC Primers cannot be used with PWR Bond 1217349 Urethane. Must use Cat. No. 1214006 One Step Primer.
    Il peso delle spedizioni è nella maggior parte dei casi approssimato e non è stato ancora verificato. Se si desidera ottenere il peso esatto, in modo tale da determinare i costi di spedizione come richiesto per completare l'ordine, si prega di richiederlo prima di inviare l'ordine contattandoCRL Assistenza al cliente.Le immagini dei prodotti sono dello stesso prodotto o di una fedele rappresentazione. ColorsI coloripossono variare a seconda della scheda video del vostro computer o del monitor e di come icolorcolorisono stati regolati.

    AB26
    CRL Pistola di calafataggio per telaio con banda, 26:1

    PWR22
    CRL POWR Pulitore vetro per autoveicoli